0750428 Falcon Brands

Service Quote#:

Rev:

Traveler Status: Schedule Status:

Prepared By:

Date Rel:

Date Quoted:

E. Ship Date:

PO#:

PO Date:

Dates Shipped:

Active:

cust id:

Identifier (30 chars):

Category:

*REP/OEM/VAR:

*Market Segment:

RMA Types

Warranty?

BILL TO

*Attn:

*Company:

Address:

City:

State:

Zip:

Country:

*Phone:

Fax:

*Email:

Rev1:

Rev2:

Rev3:

SHIP TO

Attn:

Company:

Address:

City:

State:

Zip:

Country:

Phone:

Fax:

Email:

FAT Type:

FAT Date:

Lease/Sale:

Crate/Box:

Prod. Hrs Left:

Prod. Hrs Total:

Prod. Pct Done:

Non Prod. Hrs Left:

Non Prod. Hrs Total:

Non Prod. Pct Done:

Billed Pct Done:

Price (Gross):

Project Docs:

Open in Explorer

Discount:

Quote Docs:

Open in Explorer
Copy Path

Quantity Discount:

Commission:

Price (Net):

Customer Price:

Down Payment:
Prior to Ship Payment:
Final Payment:

Down Pay Email
Ship Pay Email
Final Pay Email

✓ Wrike Down Pay
✓ Wrike Ship Pay
✓ Wrike Final Pay
★ Wrike Accounting Complete

Priority:

Override

Pay Comments:

Update Comments

Red Flag:

Don't Start Until:

Demo Equipment

R&D Project

Include in A3 Report

*Machine Serial Number:

*(Required fields)

Project Scope: The client is requesting start up assistance and training on the equipment purchased on WO#2019078.
Equipment Summary: (Machine Serial Number:Multiple)
Work Done: 12/19/19 Trip prep 1hr Bernie 1/5/20 Travel to Palm Springs 9.5hrs Travel Bernie 1/6/20 Arrived onsite, replaced sensors on first machine replaced bearing housings, started to replace shafts and when jogging line I heard a clunking noise, began to take everything apart piece by piece and all pieces individually good, after inspecting everything noticed that the lower dish charge shaft was 1" in dia and the stub shaft was 3/4" in dia. Torn everything apart and boxed it up and shipped back to MFT. 8.5hrs onsite Bernie 1/7/20 Learned that Falcon did not ship parts back to MFT. Put line one back together so they could run, helped them with running. Installed updated software in all boxes to latest version, mounted new sensors on line 2. Once line 1 was done running the fronts they switched over the backs and it would not label correctly, after fighting for a while I switched over to test material and still had some issues, went back to old software and all was good, went back to new software made one adjustment and all was good. 9.5hrs onsite Bernie 1/8/20 Started to install new parts on line 1 and line 2 was having problems labeling, the label would continue to stop half way off peel plate, tried a bunch of stuff and nothing worked, went back to old software and same issue, Talked with Dave and got it to work by turning on the option to select product thickness drive manually and all was good. Finished installing new parts on line 1, once complete the vac belt would track off when product was running, made a couple adjustments and then good. Tried putting labels down and the same thing that was happening on line 2 was happening on line 1, tried setting the manual drive and it didn't work, went back to old software and set the manual drive and all was good. Tried to get line 2 to work with new software and couldn't get it, went back to old and all good. Torn down line 2 to get it prepped for new parts tomorrow. 8hrs onsite Bernie 1/9/20 Put line 2 back together with new parts, all ran good. Tried to get new software working and it didn't, went back to old and all good. Both lines running at 50mpm. Had Falcon set up and run Littles bags and narrow boxes, all good. Sae wanted to run both lines at 100mpm, there set up wouldn't allow it, both lines ran great at 75mpm. 8hrs onsite Bernie 1/10/11 Went in just to make sure all was good and it was. 1.5hrs onsite 9.5hrs travel Bernie
Repair Quotation Notes: Completed By:

* To Refresh Totals - Click Save at Top *

Edit	XID	Part Number	Serial Number	Part Name	Complete	Total Hours	Hours Remaining	Qty	Cost	Price	Discount	Cal Price	On Hand
Edit	40868			LABOR - HOUR ON SITE (1/6/2019 - 1/10/2019)	Set Complete		0 hrs	35		$0.00	0.00	$0.00
Edit	40869			LABOR - 1/4 HOUR ON SITE	Set Complete		0 hrs	2		$0.00	0.00	$0.00
Edit	40870			LABOR - TRAVEL	Set Complete		0 hrs	19		$0.00	0.00	$0.00
Edit	40871			LABOR - ADDITIONAL CHARGES	Set Complete		0 hrs	0		$0.00
Edit	40872			TRAVEL EXPENSES - CAR	Set Complete		0 hrs	1	$260.36	$260.36	0.00	$260.36
Edit	40873			TRAVEL EXPENSES - AIRFARE, CHANGE FEES, LUGGAGE	Set Complete		0 hrs	1	$865.10	$865.10	0.00	$865.10
Edit	40874			TRAVEL EXPENSES - HOTEL (BOOKED BY FALCON BRANDS)	Set Complete		0 hrs	1		$0.00	0.00	$0.00
Edit	40875			TRAVEL EXPENSES - PARKING, MEALS, GAS	Set Complete		0 hrs	1	$417.50	$417.50	0.00	$417.50
Edit	40876			SERVICE TRIP PRE-TRAVEL PREP FEE	Set Complete		0 hrs	1		$250.00
Edit	42471	7160000		SENS BGS MLV12 PNP 250MM ADJ W/ BRACKET	Set Complete	4 Standard Production Build	4 hrs	4		$0.00	0.00	$0.00	0
Edit	42472	4107703		DRIVE ASSY RIGHT DCC-3 NPCA	Set Complete		0 hrs	2		$0.00	0.00	$0.00	68

+ denotes that software settings are available for this piece of equipment.

Labor Hours
* To Refresh Totals - Click Save at Top *

Purchase orders for this Work Order

Edit

XID

Description

Partial

Cost


Charge ID:
Charge postfix (3 chars):
Manager:
Cost Center:
Description:
Begin Date:
End Date:
Budget (hours):
	Active R & D


Serial Number:
Quantity:	Price: % Discount:
	Special cost * financial summary does multiply by quantity * (do not use for purchase orders):
	Set to Zero Production Item: Used Equipment: RMA Main Product: Cost credit
Part Number:	Multifeeder Part: Lead Time (days):
Part Name:
Flag Item:
Date Started:	Date Required: Date Shipped:
Build Pulled:	Build Mechanical: Build Electrical:
Overall Status:	Check Out #1: Check Out #2:
Notes:
Don't Start Until:
Returned
	Add/View/Edit Resource Hours


Vendor:
Description:
Purchase Order:
Total Cost:
Partial Cost:	use this if only part of the purchase order was applied to this work order


			*PRODUCT STACK SHELVES ARE NOT INCLUDED WITH BASE-PICK WHAT IS NEEDED*


			**ALL ITEMS BELOW ARE INCLUDED IN COSTING & PRICING PN 9740001**