0554588 Hu Friedy Group

RMA#:

Rev:

Traveler Status: Schedule Status:

Prepared By:

Date Rel:

Date Equip. Received:

Date Quoted:

E. Ship Date:

PO#:

PO Date:

Dates Shipped:

Active:

cust id:

Identifier (30 chars):

Category:

*REP/OEM/VAR:

RMA Types

Warranty?

BILL TO

*Attn:

*Company:

Address:

City:

State:

Zip:

Country:

*Phone:

Fax:

*Email:

Rev1:

Rev2:

Rev3:

SHIP TO

Attn:

Company:

Address:

City:

State:

Zip:

Country:

Phone:

Fax:

Email:

FAT Type:

FAT Date:

Lease/Sale:

Crate/Box:

Prod. Hrs Left:

Prod. Hrs Total:

Prod. Pct Done:

Non Prod. Hrs Left:

Non Prod. Hrs Total:

Non Prod. Pct Done:

Billed Pct Done:

Price (Gross):

Project Docs:

Open in Explorer

Discount:

Quote Docs:

Open in Explorer
Copy Path

Quantity Discount:

Commission:

Price (Net):

Customer Price:

Down Payment:
Prior to Ship Payment:
Final Payment:

Down Pay Email
Ship Pay Email
Final Pay Email

✓ Wrike Down Pay
✓ Wrike Ship Pay
✓ Wrike Final Pay
★ Wrike Accounting Complete

Priority:

Override

Pay Comments:

Update Comments

Red Flag:

Don't Start Until:

Demo Equipment

R&D Project

Include in A3 Report

*Machine Serial Number:

*(Required fields)

What Arrived: MFT 250 (Machine Serial Number:0445-07157)
Description of Problem: SOME SHIPPING DAMAGE photos attached. Welded discharge angle adjustment bent almost 90 degree. Hole in box where it pierced cardboard. probably dropped and landed on that corner. MFT 250 S/N 0445-07157 with: 2 prod support rods 1 set of magazine side giuides power cord 6 purple discharge belts 2 white (not beige) single row vacuum hole feedbelts 2 purple stripper wheel Catch tray with mounted round sensor with cable. light tower
Work Done: Reattached discharge which was removed for shipping. Flattened and reshaped the arc-shaped guides that allow the discharge to swing up and down. Upper discharge roller has too long of an axle by about 1/2 inch, requiring it to mount on homemade blocks on the outside of the discharge side brackets. roller is correct width. feedbelts are usable, lower discharge belts are passable when turned inside-out. Upper discharge belts not usable. stripper wheels rotate the wrong way due to comedy of errors. Left and right cranks are on wrong side. Need to be that way to move because both one-way bearings are in the slideblocks on the right side bearing housing only allowing belts to rotate in the direction of travel (upper discharge shaft as well as stripper wheel shaft. Noticeably more wear on upper discharge shaft surface on that side than the left, where both slide blocks have just regular bearings. Need to remove housings and switch things around correctly and regrease or replace. One lower discharge pulley damaged from grinding on left edge. Had to replace J1 connector/harness because part of the threads were broken-off and stuck inside the start sensor connector housing,. Probably from cross threading and over-tightening.. Once connector installed, passed all electrical tests except status light yellow and green no-light.OK including APL test. Prod sensor all 255. fans good. 20.20 tach when jog set to 20mpm Missing protective covers on Driver board and PS. DEK 17 oct 23 cOMPLETED 10.5 hours of burn-in without a hiccup. 18 OCT 23 Removed driva assys and replaced needle brgs and clutches into proper location. Reassembled drive assy Manually scotch-brited shafts prior to reassembly, replaced 2 discharge belt pulleys on lower shaft. Replaced feedbelt collars and feedbelts Replaced Right Housing SW sliding block, reassembled machine Added used cover for driver board initiated burn-in 8:00 pm 31 Oct 23 DEK Improvised upper discharge roller, which was oiled, began squealing metal-on-metal during vvernight burn. Stapped it afte r 9 hrs 40 min and replace with used roller discovered by David. Oiled roller ant restarted burn-in DEK 1 nov 2023 CREATED SO 044219 FOR RETURN SHIPMENT TO ELMER 2 NOV 2023 Use FEDEX FREIGHT #114870978 for return
Repair Quotation Notes: Completed By:

* To Refresh Totals - Click Save at Top *

Edit	XID	Part Number	Serial Number	Part Name	Complete	Total Hours	Hours Remaining	Qty	Cost	Price	Discount	Cal Price	On Hand
Edit	69362	7003700		START/STAT INTERCONNECT CABLE	Set Complete		0 hrs	1		$205.00	0.00	$205.00	6
Edit	69399	1168300		FEEDBELT SE 304007SV	Set Complete		0 hrs	2		$182.00	0.00	$364.00	12
Edit	69400	1096800		STRIPPER WHEEL 3042 85D	Set Complete		0 hrs	2		$281.00	0.00	$562.00	14
Edit	69401	1177300		ED DISCHARGE BELT EPDM 204604	Set Complete		0 hrs	6		$83.00	0.00	$498.00	40
Edit	69402	4142200		DISCHARGE TABLE ROD 250 S	Set Complete		0 hrs	5		$99.00	0.00	$495.00	106
Edit	69403	4127400		DISCHARGE PULLEY ASSY 2040	Set Complete		0 hrs	1		$248.00	0.00	$248.00	14
Edit	69404	1159200		TIMING BELT 0592	Set Complete		0 hrs	1		$58.00	0.00	$58.00	4
Edit	69405	1154500		TIMING BELT 0545	Set Complete		0 hrs	1		$38.00	0.00	$38.00	13
Edit	69406	6826200		BULB 24V 5W 45MM LIGHT	Set Complete		0 hrs	3		$9.00	0.00	$27.00	26
Edit	69408	1011000		NEEDLE ROLLER BEARING 162212	Set Complete		0 hrs	2		$25.00	0.00	$50.00	23
Edit	69409	1020000		NEEDLE ROLLER CLUTCH 162216	Set Complete		0 hrs	2		$91.00	0.00	$182.00	133
Edit	69410	1031000		BEARING SEAL 1622	Set Complete		0 hrs	2		$17.00	0.00	$34.00	165
Edit	69407			RMA LABOR	Set Complete		0 hrs	10		$200.00	0.00	$2,000.00
Edit	69411			REPLACEMENT SHIPPING CARTON WITH PADDING	Set Complete		0 hrs	1		$115.00	0.00	$115.00

+ denotes that software settings are available for this piece of equipment.

Labor Hours
* To Refresh Totals - Click Save at Top *

Purchase orders for this Work Order

Edit

XID

Description

Partial

Cost


Charge ID:
Charge postfix (3 chars):
Manager:
Cost Center:
Description:
Begin Date:
End Date:
Budget (hours):
	Active R & D


Serial Number:
Quantity:	Price: % Discount:
	Special cost * financial summary does multiply by quantity * (do not use for purchase orders):
	Set to Zero Production Item: Used Equipment: RMA Main Product: Cost credit
Part Number:	Multifeeder Part: Lead Time (days):
Part Name:
Flag Item:
Date Started:	Date Required: Date Shipped:
Build Pulled:	Build Mechanical: Build Electrical:
Overall Status:	Check Out #1: Check Out #2:
Notes:
Don't Start Until:
Returned
	Add/View/Edit Resource Hours


Vendor:
Description:
Purchase Order:
Total Cost:
Partial Cost:	use this if only part of the purchase order was applied to this work order


			*PRODUCT STACK SHELVES ARE NOT INCLUDED WITH BASE-PICK WHAT IS NEEDED*


			**ALL ITEMS BELOW ARE INCLUDED IN COSTING & PRICING PN 9740001**