0554531 CPI Card MN

RMA#:

Rev:

Traveler Status: Schedule Status:

Prepared By:

Date Rel:

Date Equip. Received:

Date Quoted:

E. Ship Date:

PO#:

PO Date:

Dates Shipped:

Active:

cust id:

Identifier (30 chars):

Category:

*REP/OEM/VAR:

RMA Types

Warranty?

BILL TO

*Attn:

*Company:

Address:

City:

State:

Zip:

Country:

*Phone:

Fax:

*Email:

Rev1:

Rev2:

Rev3:

SHIP TO

Attn:

Company:

Address:

City:

State:

Zip:

Country:

Phone:

Fax:

Email:

FAT Type:

FAT Date:

Lease/Sale:

Crate/Box:

Prod. Hrs Left:

Prod. Hrs Total:

Prod. Pct Done:

Non Prod. Hrs Left:

Non Prod. Hrs Total:

Non Prod. Pct Done:

Billed Pct Done:

Price (Gross):

Project Docs:

Open in Explorer

Discount:

Quote Docs:

Open in Explorer
Copy Path

Quantity Discount:

Commission:

Price (Net):

Customer Price:

Down Payment:
Prior to Ship Payment:
Final Payment:

Down Pay Email
Ship Pay Email
Final Pay Email

✓ Wrike Down Pay
✓ Wrike Ship Pay
✓ Wrike Final Pay
★ Wrike Accounting Complete

Priority:

Override

Pay Comments:

Update Comments

Red Flag:

Don't Start Until:

Demo Equipment

R&D Project

Include in A3 Report

*Machine Serial Number:

*(Required fields)

What Arrived: (Machine Serial Number:1712-09575) Unknown Issues need machine gone through and repaired to make sure it is in great working order.
Description of Problem: MFT 250 HCP3 ed 4.3.55HP current rev. software ampcode 4.12 with: (1) non-mft rough feedbelt (6) HC discharge belts (1) 30mm SW passive Pressure roller mounted. no sensors, cables , or light tower. no power cord.
Work Done: Significant bearing housing slide block play, especially left side discharge block. Backlash not bad though. timing belts look newly replaced, A little overtightened at drive motor. stripper wheel seems to slope toward right. Non-MFT turquoise 30mm feedbelt needs replacing. HC discharge belts look ok to use. 4th drive of prod sensor reads 210 max, david advises OK to keep using. will quote: Feedbelt w/shims new bearings pressure roller orings, 20mm rubber bellows lcd DISPLAY PROBABLE IMPACT DAMAGE IN LOCALIZED AREA. Replaced bearings in housings., LCD display,orings, feedbelt. Upgraded to version 5.149 amp 5.25 lcd ver 5.7 PASSES ALL TESTS AND 24HR BURN-IN 25 MAY 23 DEK Created SO 043304 to do partial ship of this RMA against PO 69149 OK'd by Billy Kirk
Repair Quotation Notes: Completed By: Recommend bearing rebuild on drive assemblies including all new bearings to eliminate play and grinding noise. Recommend new feedbelt with appropriate tensioning shims Recommend new pressure roller rubber orings to replaced dried, checked ones. Recommend LCD display replacement due to probable impact damage on right side showing solid black squares at all times. Recommend Upgrade to version 5 software which offers the following enhancements: Changes motor drive waveform creation to Sinusoidal from Sawtooth, improving motor efficiency and reducing noise . Adds overcurrent prediction for motor to generate fault when approaching overload condition. Revision 2 of quote adds magazine side guides (deeper 175mm on left, shallower 75 mm on right) plus (2) HC product support bars (curved tip) and one 25mm wide rear product support curve with mount which were missing from the machine.

* To Refresh Totals - Click Save at Top *

Edit	XID	Part Number	Serial Number	Part Name	Complete	Total Hours	Hours Remaining	Qty	Cost	Price	Discount	Cal Price	On Hand
Edit	65873	1199900		FEED BELT SE 304606R	Set Complete		0 hrs	1		$165.00	0.00	$165.00	64
Edit	65874	1002100		BALL BEARING 173510	Set Complete		0 hrs	10		$59.00	0.00	$590.00	41
Edit	66057	4125600		STRIPPER WHEEL ASSY 304620	Set Complete		0 hrs	1		$154.00	0.00	$154.00	33
Edit	66062	7001900		LCD DISPLAY 4 X 40 NHD YEL/GRN	Set Complete		0 hrs	1		$337.00	0.00	$337.00	38
Edit	65875	1045300		O-RING 326 70D N	Set Complete		0 hrs	2		$2.00	0.00	$4.00	57
Edit	65877			UPGRADE TO VERSION 5 SOFTWARE	Set Complete		0 hrs	1		$800.00	0.00	$800.00
Edit	65878			LABOR	Set Complete		0 hrs	14		$200.00	0.00	$2,800.00
Edit	66188	2390216		PRODUCT SIDE SEC TR75 20 CUT	Set Complete		0 hrs	1		$305.00	0.00	$305.00	4
Edit	66189	2390622		PRODUCT SIDE SEC TL175 20 CUT	Set Complete		0 hrs	1		$452.00	0.00	$452.00	4
Edit	66190	4249150		PROD SPPT ASSY HC TALL CRV	Set Complete		0 hrs	2		$676.00	0.00	$1,352.00	0
Edit	66191	4212100		FEEDER SUPPORT CURVE PP 25 200	Set Complete		0 hrs	1		$365.00	0.00	$365.00	13
Edit	66195	3006300		M8 X 16 ADJUSTABLE LEVER	Set Complete		0 hrs	4		$27.00	0.00	$108.00	90

+ denotes that software settings are available for this piece of equipment.

Labor Hours
* To Refresh Totals - Click Save at Top *

Purchase orders for this Work Order

Edit

XID

Description

Partial

Cost


Charge ID:
Charge postfix (3 chars):
Manager:
Cost Center:
Description:
Begin Date:
End Date:
Budget (hours):
	Active R & D


Serial Number:
Quantity:	Price: % Discount:
	Special cost * financial summary does multiply by quantity * (do not use for purchase orders):
	Set to Zero Production Item: Used Equipment: RMA Main Product: Cost credit
Part Number:	Multifeeder Part: Lead Time (days):
Part Name:
Flag Item:
Date Started:	Date Required: Date Shipped:
Build Pulled:	Build Mechanical: Build Electrical:
Overall Status:	Check Out #1: Check Out #2:
Notes:
Don't Start Until:
Returned
	Add/View/Edit Resource Hours


Vendor:
Description:
Purchase Order:
Total Cost:
Partial Cost:	use this if only part of the purchase order was applied to this work order


			*PRODUCT STACK SHELVES ARE NOT INCLUDED WITH BASE-PICK WHAT IS NEEDED*


			**ALL ITEMS BELOW ARE INCLUDED IN COSTING & PRICING PN 9740001**