0553724 Covidien

RMA#:

Rev:

Traveler Status: Schedule Status:

Prepared By:

Date Rel:

Date Equip. Received:

Date Quoted:

E. Ship Date:

PO#:

PO Date:

Dates Shipped:

Active:

cust id:

Identifier (30 chars):

Category:

*REP/OEM/VAR:

RMA Types

Warranty?

BILL TO

*Attn:

*Company:

Address:

City:

State:

Zip:

Country:

*Phone:

Fax:

*Email:

Rev1:

Rev2:

Rev3:

SHIP TO

Attn:

Company:

Address:

City:

State:

Zip:

Country:

Phone:

Fax:

Email:

FAT Type:

FAT Date:

Lease/Sale:

Crate/Box:

Prod. Hrs Left:

Prod. Hrs Total:

Prod. Pct Done:

Non Prod. Hrs Left:

Non Prod. Hrs Total:

Non Prod. Pct Done:

Billed Pct Done:

Price (Gross):

Project Docs:

Discount:

Quote Docs:

Open in Explorer
Copy Path

Quantity Discount:

Commission:

Price (Net):

Customer Price:

Down Payment:
Prior to Ship Payment:
Final Payment:

Down Pay Email
Ship Pay Email
Final Pay Email

✓ Wrike Down Pay
✓ Wrike Ship Pay
✓ Wrike Final Pay
★ Wrike Accounting Complete

Priority:

Override

Pay Comments:

Update Comments

Red Flag:

Don't Start Until:

Demo Equipment

R&D Project

Include in A3 Report

*Machine Serial Number:

*(Required fields)

What Arrived: Customer wants to send in 250 feeder and drop table. Customer indicating the drop table does not go all the way in and sometimes they go too far back and then it does not return fast enough. Then it goes like a machine gun and goes back and forth. (Machine Serial Number: ) Customer wants an new drop table for older mahcines mft 350(
Description of Problem: (1) MFT 250 XED SN: 0144-01991 (2) 30mm rough natural feed belts (2) 30mm stripper wheels (4) 20mm discharge belts (1) ER pair (1) Low Product Sensor (1) Stack light (1) Rear support curve (2) Magazine side plates (2) product support rods (2) Power cords (1) ADT250 SN: 0050-01714 (3) Product rods (2) Side plates (1) back plate (1) Upper ski (1) ADT to Feeder Cable
Work Done: Checked in and inspected machine. Put into testing and found drop table to be operating multiple times per cycle and incrementing up one time every few minutes. Installed new ER pari on feeder to get into testing 8/22/2017 MM Found K5 of the ADT Interface Board was causing multiple cycle of ADT. ADT passed a 20minnute test with customers machine, and diagnostics. Found Fuse blown for over current of Feeder Rectifier Board. Replaced FETS in rectifier board, to solve problem. Completed evaluation of ADT and Feeder. Put Feeder in burn in, and observed for proper operation. Completed repair quote, and emailed to the customer. 8/29/17 DK FOC Discharge Pulley 4127400, as the groove may have happen in testing. 8/29/17 DK Continued work. Completed work to the Feeder. Put into burn in, and observed for proper operation. 9/6/17 Feeder passed 24 hour burn in, and check out. Completed work to the ADT. Set up machines to run customer samples. Saw software was set for Discrete Input of Stop Motor through J3, Sent to shipping. SO# 030049 9/8/17 DK
Repair Quotation Notes: Completed By: Found a Relay was failing causing the intermittent multiple cycles of the ADT, and speed changes. ADT Interface Cable ASSY was spliced into, in a non recommended way for customer interface. Will replace Assembly and splice in customer interface plug in a recommended way. Static Brush for ADT is worn, and should be replaced. HEXFET shorted on Feeder Rectifier Board causing the Resistor to burn out, and Fuse to blow. Two Bulbs in the stack light burnt out. Sensor Pair is not reading as strong as it should, recommend replacing it. Feeder is missing filters for electrical enclosure. Recommend replacing Spanning Pulleys for new version recommended for Feed Belts used. Collars to align Spanning Pulleys for Feed Belts are missing. Feed Belts, Stripper Wheels, and Discharge Belts, are worn, recommend replacing.

* To Refresh Totals - Click Save at Top *

Edit	XID	Part Number	Serial Number	Part Name	Complete	Total Hours	Hours Remaining	Qty	Cost	Price	Discount	Cal Price	On Hand
Edit	30174	5432100		RELAY 120MA 8-PIN DIP	Set Complete		0 hrs	1		$28.00	0.00	$28.00	12
Edit	30175	7103900		ADT INTERFACE CABLE ASSY	Set Complete		0 hrs	1		$110.00	0.00	$110.00	0
Edit	30176	1710900		STATIC BRUSH	Set Complete		0 hrs	1		$4.00	0.00	$4.00	2
Edit	30178	6336500		HEXFET N-CHANN POWER TO-247AC	Set Complete		0 hrs	2		$24.00	0.00	$48.00	4
Edit	30180	6511000		RES 10 OHM 50 W	Set Complete		0 hrs	1		$26.00	0.00	$26.00	1
Edit	30181	6392500		FUSE 250 V MDL 3 1.25" X .25"	Set Complete		0 hrs	1		$5.00	0.00	$5.00	6
Edit	30182	6826100		STS-24V-5W BULB	Set Complete		0 hrs	2		$17.00	0.00	$34.00	19
Edit	30183	7006600		XED DISCH PROD SENSOR PAIR ASY	Set Complete		0 hrs	1		$364.00	0.00	$364.00	8
Edit	30184	3755000		FEEDER LID FRONT FILTER	Set Complete		0 hrs	1		$4.00	0.00	$4.00	40
Edit	30185	3755100		FEEDER LID REAR FILTER	Set Complete		0 hrs	1		$4.00	0.00	$4.00	58
Edit	30186	4120200		SPANNING PULLEY ASSY 3040	Set Complete		0 hrs	2		$158.00	0.00	$316.00	5
Edit	30187	4121000		COLLAR FEEDBELT INT 16MM	Set Complete		0 hrs	3		$47.00	0.00	$141.00	34
Edit	30188	1167300		FEEDBELT SE 304007R	Set Complete		0 hrs	2		$170.00	0.00	$340.00	18
Edit	30189	1096800		STRIPPER WHEEL 3042	Set Complete		0 hrs	2		$117.00	0.00	$234.00	14
Edit	30190	1178300		ED DISCHARGE BELT EPDM 204003	Set Complete		0 hrs	4		$84.00	0.00	$336.00	23
Edit	30192			LABOR	Set Complete		0 hrs	16		$165.00	0.00	$2,640.00

+ denotes that software settings are available for this piece of equipment.

Labor Hours
* To Refresh Totals - Click Save at Top *

Purchase orders for this Work Order

Edit

XID

Description

Partial

Cost


Charge ID:
Charge postfix (3 chars):
Manager:
Cost Center:
Description:
Begin Date:
End Date:
Budget (hours):
	Active R & D


Serial Number:
Quantity:	Price: % Discount:
	Special cost * financial summary does multiply by quantity * (do not use for purchase orders):
	Set to Zero Production Item: Used Equipment: RMA Main Product: Cost credit
Part Number:	Multifeeder Part: Lead Time (days):
Part Name:
Flag Item:
Date Started:	Date Required: Date Shipped:
Build Pulled:	Build Mechanical: Build Electrical:
Overall Status:	Check Out #1: Check Out #2:
Notes:
Don't Start Until:
Returned
	Add/View/Edit Resource Hours


Vendor:
Description:
Purchase Order:
Total Cost:
Partial Cost:	use this if only part of the purchase order was applied to this work order


			*PRODUCT STACK SHELVES ARE NOT INCLUDED WITH BASE-PICK WHAT IS NEEDED*


			**ALL ITEMS BELOW ARE INCLUDED IN COSTING & PRICING PN 9740001**