0552701 Eath Thebault

RMA#:

Rev:

Traveler Status: Schedule Status:

Prepared By:

Date Rel:

Date Equip. Received:

Date Quoted:

E. Ship Date:

PO#:

PO Date:

Dates Shipped:

Active:

cust id:

Identifier (30 chars):

Category:

*REP/OEM/VAR:

RMA Types

Warranty?

BILL TO

*Attn:

*Company:

Address:

City:

State:

Zip:

Country:

*Phone:

Fax:

*Email:

Rev1:

Rev2:

Rev3:

SHIP TO

Attn:

Company:

Address:

City:

State:

Zip:

Country:

Phone:

Fax:

Email:

FAT Type:

FAT Date:

Lease/Sale:

Crate/Box:

Prod. Hrs Left:

Prod. Hrs Total:

Prod. Pct Done:

Non Prod. Hrs Left:

Non Prod. Hrs Total:

Non Prod. Pct Done:

Billed Pct Done:

Price (Gross):

Project Docs:

Discount:

Quote Docs:

Open in Explorer
Copy Path

Quantity Discount:

Commission:

Price (Net):

Customer Price:

Down Payment:
Prior to Ship Payment:
Final Payment:

Down Pay Email
Ship Pay Email
Final Pay Email

✓ Wrike Down Pay
✓ Wrike Ship Pay
✓ Wrike Final Pay
★ Wrike Accounting Complete

Priority:

Override

Pay Comments:

Update Comments

Red Flag:

Don't Start Until:

Demo Equipment

R&D Project

Include in A3 Report

*Machine Serial Number:

*(Required fields)

What Arrived: (Machine Serial Number:unknown at this time)Motor will not run. Tried new motor. Checked motor cables, and interlock.
Description of Problem: MFT 350 IP ED DCC SN 0805-08028 (3) 30mm SE R Feed Belts (3) 30mm Stripper wheels (6) 20mm discharge belts1 (1) 25mm rear support curve (2) H blocks for mounting (on feeders feet) (1) interlock plug (1) e/r pair (1) ML17 Start Sensor W/ bracket (1) LSE W/ bracket (1) 120 v power cord
Work Done: Found that U38 opt isolator between AMP DSP and Power X has failed causing the motor to be unable to run. Chong to replace. Composite pulleys and gears should be replaced. 11/20/12 DK Chong replaced U38 and mother board assembly is fully functional. 11/21/12 Mounted motherboard assembly in feeder, and completed evaluation. Sent customer repair quote. 11/27/12 DK Resumed work on the feeder. With email ok to the quote. 11/28/12 DK Completed work to the feeder. Put feeder in burn in and observed for proper operation. 12/3/12 DK Feeder passed burn in, and check out. Ready to ship via UPS GND. SO# 19052 12/4/12 DK
Repair Quotation Notes: Completed By: Found an Opto Isolator failed on the motherboard causing the machine to be unable to run the motor. A cooling fan has broken blades. The Keypad has a crack allowing dust and debris to accumulate on the LCD display. Exit roller brackets are cracked. Stripper wheels have deep gauges. Discharge belts are in need of replacing. Center piece shaft for upper discharge shaft has deep grooves. This is not an issue as long as the belts do not have to be positioned over the grooves. The rest or the items are to replace the composite pulleys and gears with metal versions. This will dramatically increase the machines ability to accurately place products. The exit roller bearings are a little worn, but they have some life in them. Considering the price of the exit rollers it would be worth it to run them further. Repair quote does not reflect final charges for service of this unit. Other problems either mechanical or electrical may arise during the RMA process due to natural causes. Quoted labor is an estimate. Actual labor time will be billed. This quote does not reflect shipping charges. All items will be shipped via UPS ground unless otherwise specified on purchase order. A $475.00 diagnostic/administration/handling fee will be applied to an item the customer deems is uneconomical to repair. All replaced and un-repairable items will be disposed of, unless otherwise stated on purchase order. * A hard copy purchase order that agrees to repair quote charges is required before work can continue.

* To Refresh Totals - Click Save at Top *

Edit	XID	Part Number	Serial Number	Part Name	Complete	Total Hours	Hours Remaining	Qty	Cost	Price	Discount	Cal Price	On Hand
Edit	16552	6211400		PHOTO OPTOISO 10MBPS 5SMD	Set Complete		0 hrs	1		$16.00			28
Edit	16553	7018700		FAN ASSEMBLY 80 X 80 X 15 213W	Set Complete		0 hrs	1		$107.00			17
Edit	16554	5311000		MEMBRANE KEYPAD MFT	Set Complete		0 hrs	1		$315.00			53
Edit	16555	4310000		DISCHARGE SLIDING BLOCK ASSY	Set Complete		0 hrs	2		$233.00			108
Edit	16556	1097300		STRIPPER WHEEL 304620 85D	Set Complete		0 hrs	3		$88.00			483
Edit	16557	1177300		ED DISCHARGE BELT EPDM 204604	Set Complete		0 hrs	6		$78.00			40
Edit	16558	1263700		CENTER PIECE SHAFT 350 20	Set Complete		0 hrs	1		$185.00			85
Edit	16559	1053900		TIMING PULLEY 051524 16 AF	Set Complete		0 hrs	1		$82.00			41
Edit	16560	1054000		TIMING PULLEY 051530 16 AF	Set Complete		0 hrs	1		$88.00			46
Edit	16561	1057300		TIMING PULLEY 9521311 AF	Set Complete		0 hrs	2		$76.00			64
Edit	16562	4129400		SPUR GEAR 16 475 525 ALF	Set Complete		0 hrs	2		$117.00			39
Edit	16563			LABOR	Set Complete		0 hrs	8		$125.00

+ denotes that software settings are available for this piece of equipment.

Labor Hours
* To Refresh Totals - Click Save at Top *

Purchase orders for this Work Order

Edit

XID

Description

Partial

Cost


Charge ID:
Charge postfix (3 chars):
Manager:
Cost Center:
Description:
Begin Date:
End Date:
Budget (hours):
	Active R & D


Serial Number:
Quantity:	Price: % Discount:
	Special cost * financial summary does multiply by quantity * (do not use for purchase orders):
	Set to Zero Production Item: Used Equipment: RMA Main Product: Cost credit
Part Number:	Multifeeder Part: Lead Time (days):
Part Name:
Flag Item:
Date Started:	Date Required: Date Shipped:
Build Pulled:	Build Mechanical: Build Electrical:
Overall Status:	Check Out #1: Check Out #2:
Notes:
Don't Start Until:
Returned
	Add/View/Edit Resource Hours


Vendor:
Description:
Purchase Order:
Total Cost:
Partial Cost:	use this if only part of the purchase order was applied to this work order


			*PRODUCT STACK SHELVES ARE NOT INCLUDED WITH BASE-PICK WHAT IS NEEDED*


			**ALL ITEMS BELOW ARE INCLUDED IN COSTING & PRICING PN 9740001**