0552607 Xpedx Greensboro

RMA#:

Rev:

Traveler Status: Schedule Status:

Prepared By:

Date Rel:

Date Equip. Received:

Date Quoted:

E. Ship Date:

PO#:

PO Date:

Dates Shipped:

Active:

cust id:

Identifier (30 chars):

Category:

*REP/OEM/VAR:

RMA Types

Warranty?

BILL TO

*Attn:

*Company:

Address:

City:

State:

Zip:

Country:

*Phone:

Fax:

*Email:

Rev1:

Rev2:

Rev3:

SHIP TO

Attn:

Company:

Address:

City:

State:

Zip:

Country:

Phone:

Fax:

Email:

FAT Type:

FAT Date:

Lease/Sale:

Crate/Box:

Prod. Hrs Left:

Prod. Hrs Total:

Prod. Pct Done:

Non Prod. Hrs Left:

Non Prod. Hrs Total:

Non Prod. Pct Done:

Billed Pct Done:

Price (Gross):

Project Docs:

Discount:

Quote Docs:

Open in Explorer
Copy Path

Quantity Discount:

Commission:

Price (Net):

Customer Price:

Down Payment:
Prior to Ship Payment:
Final Payment:

Down Pay Email
Ship Pay Email
Final Pay Email

✓ Wrike Down Pay
✓ Wrike Ship Pay
✓ Wrike Final Pay
★ Wrike Accounting Complete

Priority:

Override

Pay Comments:

Update Comments

Red Flag:

Don't Start Until:

Demo Equipment

R&D Project

Include in A3 Report

*Machine Serial Number:

*(Required fields)

What Arrived: Signal light issue. Red light always one. (Machine Serial Number:unknown at this time)
Description of Problem: (1) Interface Board PN 70502-0B SN 3610
Work Done: Found that R22 for Red light output has overheared, and caused R9 on the other side of the board to fall off. R23 also has a burnt mark. Replaced all three of these resistors. One of the barrles for R22 was two damaged to save from the over heating Soldered the other end to Q7 were it is electricaly connected. 5/16/12 DK Found Q7 was shorted out. Replaced the trinsitor, and board passed all tests. Checked that the new postion of the resistor would not interfere or short anything out. Told Greg what had been done, and he approved the repair. Emailed customer repair quote. 5/17/12 DK Received PO. Ready to ship. SO# 18030 5/30/12 DK
Repair Quotation Notes: Completed By: Found that the 10 ohm 3 watt current limiting resistor for the red lamp had overheated. This caused the adjacent current limiting resistor for the stack light to overheat, and a resistor on the other side of the board to become unsoldered. The FET that controlled the red lamp had shorted from source to drain. Please verify the stack light is using 5w bulbs. If it were using larger watt bulbs this would have caused the failure. Repair quote does not reflect final charges for service of this unit. Other problems either mechanical or electrical may arise during the RMA process due to natural causes. Quoted labor is an estimate. Actual labor time will be billed. This quote does not reflect shipping charges. All items will be shipped via UPS ground unless otherwise specified on purchase order. A $475.00 diagnostic/administration/handling fee will be applied to an item the customer deems is uneconomical to repair. All replaced and un-repairable items will be disposed of, unless otherwise stated on purchase order. * A hard copy purchase order that agrees to repair quote charges is required before work can continue.


Serial Number:
Quantity:	Price: % Discount:
	Special cost * financial summary does multiply by quantity * (do not use for purchase orders):
	Set to Zero Production Item: Used Equipment: RMA Main Product: Cost credit
Part Number:	Multifeeder Part: Lead Time (days):
Part Name:
Flag Item:
Date Started:	Date Required: Date Shipped:
Build Pulled:	Build Mechanical: Build Electrical:
Overall Status:	Check Out #1: Check Out #2:
Notes:
Don't Start Until:
Returned
	Add/View/Edit Resource Hours


Vendor:
Description:
Purchase Order:
Total Cost:
Partial Cost:	use this if only part of the purchase order was applied to this work order


Charge ID:
Charge postfix (3 chars):
Manager:
Cost Center:
Description:
Begin Date:
End Date:
Budget (hours):
	Active R & D


			*PRODUCT STACK SHELVES ARE NOT INCLUDED WITH BASE-PICK WHAT IS NEEDED*


			**ALL ITEMS BELOW ARE INCLUDED IN COSTING & PRICING PN 9740001**