0552422 Colbert Packaging / Thompson Direct*

RMA#:

Rev:

Traveler Status: Schedule Status:

Prepared By:

Date Rel:

Date Equip. Received:

Date Quoted:

E. Ship Date:

PO#:

PO Date:

Dates Shipped:

Active:

cust id:

Identifier (30 chars):

Category:

*REP/OEM/VAR:

RMA Types

Warranty?

BILL TO

*Attn:

*Company:

Address:

City:

State:

Zip:

Country:

*Phone:

Fax:

*Email:

Rev1:

Rev2:

Rev3:

SHIP TO

Attn:

Company:

Address:

City:

State:

Zip:

Country:

Phone:

Fax:

Email:

FAT Type:

FAT Date:

Lease/Sale:

Crate/Box:

Prod. Hrs Left:

Prod. Hrs Total:

Prod. Pct Done:

Non Prod. Hrs Left:

Non Prod. Hrs Total:

Non Prod. Pct Done:

Billed Pct Done:

Price (Gross):

Project Docs:

Discount:

Quote Docs:

Open in Explorer
Copy Path

Quantity Discount:

Commission:

Price (Net):

Customer Price:

Down Payment:
Prior to Ship Payment:
Final Payment:

Down Pay Email
Ship Pay Email
Final Pay Email

✓ Wrike Down Pay
✓ Wrike Ship Pay
✓ Wrike Final Pay
★ Wrike Accounting Complete

Priority:

Override

Pay Comments:

Update Comments

Red Flag:

Don't Start Until:

Demo Equipment

R&D Project

Include in A3 Report

*Machine Serial Number:

*(Required fields)

What Arrived: Feeder not keeping accuracy in tipping. HC discharge belts, and software update may be the answer. (Machine Serial Number:0508-06124)
Description of Problem: MFT 250 XED IP SN 0508-06124 on a swivel stand. (1) 10mm R SE feed belt (1) 10mm stripper wheel (2) 10mm discharge belts 1/1 (2) 20mm discharge belts 1/1 (1) 18mm wide rear support curve (1) set of mag side guide assy. (1) product support rod assy (2) 10mm belt guides (1) set of HD discharge side guiding (1) sick start sensor with mount (1) LSE with mount (1) Stack light (1) e/r pair (1) 230v power cord
Work Done: Feeder’s software has been updated to the highest level supported by the hardware of the feeder when the machine was in the shop in 9/09. The feeder was reconfigured at that time to run narrow product. 5/13/11 DK Feeder is fully functional. Prepared repair quote for feeder. 5/16/11 DK Dion called and questioned the size of the exit rollers. Jim I. described a discharge with a smaller diameter exit roller then standard. This discharge is just about to be released. Pushed to get a lead time and price internally. 5/17/11 Sent revised PO with 16mm diameter exit roller HC discharge to the customer. 5/18/11 DK After seeing the quote for the HC discharge with 16mm wide exit rollers customer changed their mind. They now want the standard HC discharge. 5/23/11 DK Made shop order for custom 10mm HC discharge belts, the pulleys for them, and milling of the discharge side guides. 5/25/11 DK Received parts back from the shop. 5/26/11 DK Resumed work on the feeder. Need to pull an extra feed belt from stock, because one was twisted. 6/1/11 DK Completed work to the feeder. Put feeder in burn in and observed for proper operation. Discharge belts showed next to no side to side movement. 6/2/11 Feeder passed an 18 hour burn in, and check out. Ready to ship via freight. Called Dion to confirm billing to Thompson, and shipping to Colbert. Sales order# 16149 6/3/11 DK David, when you switch out the discharge for Colbert be sure and save ALL pieces you are replacing as they want these back. Bad or Good they want them back.
Repair Quotation Notes: Completed By: Feed belt and the stripper wheel are in need of replacing. The white collars for the spanning pulley are cracked. The next three line items are need for the hard carcass discharge belts. Custom collars for the exit roller are required for this application. Two of the hard carcass discharge belts and two of the pulleys for the belts will need to be customized for the feeder to run this narrow product. FYI with hard carcass discharge belts the angle of the discharge is fixed in one position. Discharge quoted has larger exit rollers then the current discharge. Feeder has the highest level of software that is supported by the electronics of the machine. Repair quote does not reflect final charges for service of this unit. Other problems either mechanical or electrical may arise during the RMA process due to natural causes. Quoted labor is an estimate. Actual labor time will be billed. This quote does not reflect shipping charges. All items will be shipped via UPS ground unless otherwise specified on purchase order. A $475.00 diagnostic/administration/handling fee will be applied to an item the customer deems is uneconomical to repair. All replaced items will be disposed of, unless other wise stated on purchase order. * A hard copy purchase order that agrees to repair quote charges is required before work can continue.


Serial Number:
Quantity:	Price: % Discount:
	Special cost * financial summary does multiply by quantity * (do not use for purchase orders):
	Set to Zero Production Item: Used Equipment: RMA Main Product: Cost credit
Part Number:	Multifeeder Part: Lead Time (days):
Part Name:
Flag Item:
Date Started:	Date Required: Date Shipped:
Build Pulled:	Build Mechanical: Build Electrical:
Overall Status:	Check Out #1: Check Out #2:
Notes:
Don't Start Until:
Returned
	Add/View/Edit Resource Hours


Vendor:
Description:
Purchase Order:
Total Cost:
Partial Cost:	use this if only part of the purchase order was applied to this work order

Edit	XID	Part Number	Serial Number	Part Name	Complete	Total Hours	Hours Remaining	Qty	Cost	Price	Discount	Cal Price	On Hand
Edit	13831	1199700		FEED BELT SE 104606R	Set Complete		0 hrs	1		$93.00			23
Edit	13832	1097100		STRIPPER WHEEL 104620	Set Complete		0 hrs	1		$173.00			36
Edit	13833	4120900		COLLAR FEEDBELT IP 20MM	Set Complete		0 hrs	2		$21.00			104
Edit	13834	4419020		DISCHARGE 250 XLD A35 HC	Set Complete		0 hrs	1		$3,993.00			0
Edit	13835	1186844		DISCH BELT XLD 6002001 HC44	Set Complete		0 hrs	4		$54.00			8
Edit	13836	1071744		DISCHARGE PULLEY 204620K HC44	Set Complete		0 hrs	4		$74.00			29
Edit	13838			LABOR	Set Complete		0 hrs	10		$125.00


Charge ID:
Charge postfix (3 chars):
Manager:
Cost Center:
Description:
Begin Date:
End Date:
Budget (hours):
	Active R & D


			*PRODUCT STACK SHELVES ARE NOT INCLUDED WITH BASE-PICK WHAT IS NEEDED*


			**ALL ITEMS BELOW ARE INCLUDED IN COSTING & PRICING PN 9740001**