0552173 ASO corp. FL

RMA#:

Rev:

Traveler Status: Schedule Status:

Prepared By:

Date Rel:

Date Equip. Received:

Date Quoted:

E. Ship Date:

PO#:

PO Date:

Dates Shipped:

Active:

cust id:

Identifier (30 chars):

Category:

*REP/OEM/VAR:

RMA Types

Warranty?

BILL TO

*Attn:

*Company:

Address:

City:

State:

Zip:

Country:

*Phone:

Fax:

*Email:

Rev1:

Rev2:

Rev3:

SHIP TO

Attn:

Company:

Address:

City:

State:

Zip:

Country:

Phone:

Fax:

Email:

FAT Type:

FAT Date:

Lease/Sale:

Crate/Box:

Prod. Hrs Left:

Prod. Hrs Total:

Prod. Pct Done:

Non Prod. Hrs Left:

Non Prod. Hrs Total:

Non Prod. Pct Done:

Billed Pct Done:

Price (Gross):

Project Docs:

Discount:

Quote Docs:

Open in Explorer
Copy Path

Quantity Discount:

Commission:

Price (Net):

Customer Price:

Down Payment:
Prior to Ship Payment:
Final Payment:

Down Pay Email
Ship Pay Email
Final Pay Email

✓ Wrike Down Pay
✓ Wrike Ship Pay
✓ Wrike Final Pay
★ Wrike Accounting Complete

Priority:

Override

Pay Comments:

Update Comments

Red Flag:

Don't Start Until:

Demo Equipment

R&D Project

Include in A3 Report

*Machine Serial Number:

*(Required fields)

What Arrived: Error message major product jam cannot clear. Possibl Refurbish. Mid late feb. bussy season (Machine Serial Number:0418-07102)
Description of Problem: MFT 250 ED w/ table INT (2) 20mm red r fb (2) 20mm plum sw (4) 20mm dis belts (1) set tall mag side guides (2) tall product support curves (1) 50mm s shaped support curve (1) piece 10/10 mounted to back of feeder (1) stack light (1) e/r pair
Work Done: Evaluated feeder found that when feeder went into major product jam d27 on amp board was only partialy illumanated. Found 15v from u46 dc to dc convertor was at about 11v. With component unloaded power level was normal. Replaced u46 anyways as this is a common failure, and not uncommon for voltage to be noraml unloaded. After replacing commponent feeder ran for an 18 hr burn in with out a fault. 1/26/10 DK Evaluated feeder's mech and prepared repair quote. 1/26/10 DK Receved PO 2/3/10 DK Continued work 2/5/10 DK Compleated work, and put feeder in burn in. DK 2/10/10 Feeder compleated burn in and check out. DK 2/11/10 Feeder ready to ship via UPS GND. 2/12/10 DK
Repair Quotation Notes: Completed By: Found that a DC to DC convertor was not outputting the proper voltage causing the intermittent major product jam. After replacing this component the feeder passed an eighteen hour test. There is mechanical slippage between the center piece shaft and the two end piece shafts. The plastic spur gear teeth have worn. One of the timing pulleys has a severely bent flange that cannot be straightened. Delivery exit brackets at end of feeder a severely bent up. Two of the discharge pulleys have severely gauges. The collars for the feed belts are cracked. Feed belts, discharge belts, and stripper wheels are in need of replacement. Bearings are worn. Running a feeder with seized bearings causes exes load to electronics, and motor. Repair quote does not reflect final charges for service of this unit. Other problems either mechanical or electrical may arise during the RMA process due to natural causes. This quote does not reflect shipping charges. All items will be shipped via UPS ground unless otherwise specified on purchase order. * A hard copy purchase order that agrees to repair quote charges is required before work can continue.

* To Refresh Totals - Click Save at Top *

Edit	XID	Part Number	Serial Number	Part Name	Complete	Total Hours	Hours Remaining	Qty	Cost	Price	Discount	Cal Price	On Hand
Edit	10440	5501800		POW SPPLY DC-DC CONV SGL OUT	Set Complete		0 hrs	1		$36.00			0
Edit	10441	1262700		CENTER PIECE SHAFT 250 20	Set Complete		0 hrs	1		$136.00			107
Edit	10442	1260000		END PIECE THREE PIECE SHAFT	Set Complete		0 hrs	2		$133.00			12
Edit	10443	1101000		PLASTIC SPUR GEAR	Set Complete		0 hrs	2		$55.00			4
Edit	10444	1052500		TIMING PULLEY 051525 9.5B	Set Complete		0 hrs	1		$30.00			3
Edit	10445	2020400		DELIVERY EXIT BRACKET S	Set Complete		0 hrs	2		$156.00			3
Edit	10446	4127400		DISCHARGE PULLEY ASSY 2040	Set Complete		0 hrs	2		$50.00			14
Edit	10447	4121000		COLLAR FEEDBELT INT 16MM	Set Complete		0 hrs	4		$22.00			34
Edit	10448	1167200		FEEDBELTS SE 204007R	Set Complete		0 hrs	2		$114.00			13
Edit	10449	1094800		STRIPPER WHEEL 2042	Set Complete		0 hrs	2		$65.00			2
Edit	10450	1178300		ED DISCHARGE BELT EPDM 204003	Set Complete		0 hrs	4		$56.00			23
Edit	10451			BEARING REBUILD	Set Complete		0 hrs	1		$650.00
Edit	10452			LABOR	Set Complete		0 hrs	8		$125.00

+ denotes that software settings are available for this piece of equipment.

Labor Hours
* To Refresh Totals - Click Save at Top *

Purchase orders for this Work Order

Edit

XID

Description

Partial

Cost


Charge ID:
Charge postfix (3 chars):
Manager:
Cost Center:
Description:
Begin Date:
End Date:
Budget (hours):
	Active R & D


Serial Number:
Quantity:	Price: % Discount:
	Special cost * financial summary does multiply by quantity * (do not use for purchase orders):
	Set to Zero Production Item: Used Equipment: RMA Main Product: Cost credit
Part Number:	Multifeeder Part: Lead Time (days):
Part Name:
Flag Item:
Date Started:	Date Required: Date Shipped:
Build Pulled:	Build Mechanical: Build Electrical:
Overall Status:	Check Out #1: Check Out #2:
Notes:
Don't Start Until:
Returned
	Add/View/Edit Resource Hours


Vendor:
Description:
Purchase Order:
Total Cost:
Partial Cost:	use this if only part of the purchase order was applied to this work order


			*PRODUCT STACK SHELVES ARE NOT INCLUDED WITH BASE-PICK WHAT IS NEEDED*


			**ALL ITEMS BELOW ARE INCLUDED IN COSTING & PRICING PN 9740001**