0552122 Perfect Finishing

RMA#:

Rev:

Traveler Status: Schedule Status:

Prepared By:

Date Rel:

Date Equip. Received:

Date Quoted:

E. Ship Date:

PO#:

PO Date:

Dates Shipped:

Active:

cust id:

Identifier (30 chars):

Category:

*REP/OEM/VAR:

RMA Types

Warranty?

BILL TO

*Attn:

*Company:

Address:

City:

State:

Zip:

Country:

*Phone:

Fax:

*Email:

Rev1:

Rev2:

Rev3:

SHIP TO

Attn:

Company:

Address:

City:

State:

Zip:

Country:

Phone:

Fax:

Email:

FAT Type:

FAT Date:

Lease/Sale:

Crate/Box:

Prod. Hrs Left:

Prod. Hrs Total:

Prod. Pct Done:

Non Prod. Hrs Left:

Non Prod. Hrs Total:

Non Prod. Pct Done:

Billed Pct Done:

Price (Gross):

Project Docs:

Discount:

Quote Docs:

Open in Explorer
Copy Path

Quantity Discount:

Commission:

Price (Net):

Customer Price:

Down Payment:
Prior to Ship Payment:
Final Payment:

Down Pay Email
Ship Pay Email
Final Pay Email

✓ Wrike Down Pay
✓ Wrike Ship Pay
✓ Wrike Final Pay
★ Wrike Accounting Complete

Priority:

Override

Pay Comments:

Update Comments

Red Flag:

Don't Start Until:

Demo Equipment

R&D Project

Include in A3 Report

*Machine Serial Number:

*(Required fields)

What Arrived: (Machine Serial Number:0229-02100)Feeder has false major product jam, and does not respond to power switch. Customer recently purchased from third party feeder orginaly sold to Hogue Printing.
Description of Problem: MFT 250 XED w/ table SN 0229-02100 (3) 20mm r plum hab feed belts (3) 20mm plum sw (6) 20mm XED dis belts (1) signal light (1) e/r pair (1) keyance barcode reader w/ barcode head, sensor, feeder interface cable, and power cord Box in good shape
Work Done: Found that AMP board had burnt components, led would never light, and this caused the motor to be unable to run. Replaced AMP board and feeder is functioning electricly besides the power switch that failed closed. Tested functionality of Keyance barcode reader with feeder it is functional. 10/21/09 Found mecincal slipage in mating of center piece shaft and end piece shaft on discharge. Compleated repair quote including missing items to form hopper, and other mecincal items. 10/22/09 Customer said he did not want all items to be replaced as he had an inventory of feeder parts. Attempted to sell the entire refurb as he would not save that much on labor as the mech slipage must be taken care of. Revised quote to reflect customer request. 10/27/09 DK Recived PO 10/28/09 DK Compleated refurb. 11/3/09 Feeder passed burn in and check out. 11/4/09 DK Ship feeder via ups gnd
Repair Quotation Notes: Completed By: Found that AMP board was causing motor not to function. AMP board had components with physical damage. This board is purchased from a vendor, and we do not have a complete schematic making the board un-repairable. The power switch has failed closed. The Keyence barcode reader is functional with feeder. Feeder discharge belts are in need of replacing. Recommend using a wide 30mm feed belt and a 30mm wide stripper wheel for this product. The delivery exit brackets are bent up beyond the point of strighting, and this makes it impossible to get the right tension at the exit of the discharge. The spur gears are worn. A mechanical slippage has occurred in the junction of the center piece shaft, and the end piece shaft. This slippage will cause major problems due to the fact the electronics compare the pulses from motor encoder and signals from product sensor, and do not know what is happing in the middle. Product support rod, magazine side plates, and there brackets, as well as the product support curve assembly are needed to form the hopper for this product. The feeders bearings are worn, running a feeder with bearings in this condition causes excess load to motor, and electronics. Repair quote does not reflect final charges for service of this unit. Other problems either mechanical or electrical may arise during the RMA process due to natural causes. This quote does not reflect shipping charges, shipping material or box. All items will be shipped via UPS ground unless otherwise specified on purchase order. * A hard copy purchase order that agrees to repair quote charges is required before work can continue.


Serial Number:
Quantity:	Price: % Discount:
	Special cost * financial summary does multiply by quantity * (do not use for purchase orders):
	Set to Zero Production Item: Used Equipment: RMA Main Product: Cost credit
Part Number:	Multifeeder Part: Lead Time (days):
Part Name:
Flag Item:
Date Started:	Date Required: Date Shipped:
Build Pulled:	Build Mechanical: Build Electrical:
Overall Status:	Check Out #1: Check Out #2:
Notes:
Don't Start Until:
Returned
	Add/View/Edit Resource Hours


Vendor:
Description:
Purchase Order:
Total Cost:
Partial Cost:	use this if only part of the purchase order was applied to this work order

Edit	XID	Part Number	Serial Number	Part Name	Complete	Total Hours	Hours Remaining	Qty	Cost	Price	Discount	Cal Price	On Hand
Edit	9872	7033000		PWM MOTOR AMPLIFIER PCB ASSY	Set Complete		0 hrs	1		$2,495.00			0
Edit	9873	5301600		POWER SWITCH 120 VAC 20 A	Set Complete		0 hrs	1		$3.00			4
Edit	9874	4121300		SPANNING PULLEY ASSY 304007	Set Complete		0 hrs	1		$80.00			8
Edit	9875	4122300		DRIVE PULLEY ASSY 304007	Set Complete		0 hrs	1		$58.00			10
Edit	9876	1163300		FEEDBELT 304007R	Set Complete		0 hrs	1		$59.00			18
Edit	9881	1260000		END PIECE THREE PIECE SHAFT	Set Complete		0 hrs	1		$107.00			12
Edit	9882	1262500		CENTER THREE PIECE SHAFT 250	Set Complete		0 hrs	1		$135.00			3
Edit	9890			LABOR	Set Complete		0 hrs	5		$125.00


Charge ID:
Charge postfix (3 chars):
Manager:
Cost Center:
Description:
Begin Date:
End Date:
Budget (hours):
	Active R & D


			*PRODUCT STACK SHELVES ARE NOT INCLUDED WITH BASE-PICK WHAT IS NEEDED*


			**ALL ITEMS BELOW ARE INCLUDED IN COSTING & PRICING PN 9740001**